34 3M? Multi-touch Display M2256PW User Guide
3M Touch Systems, Inc. Proprietary Information – 37531 Rev D
Calibrate Procedure
To use the CX command:
1. Enter the Calibrate (CX) command. The controller sends an initial acknowledgment
of <SOH>0<CR>.
2. Touch the sensor at a lower left target, which is located 12.5% (1/8) in from the
corner of the video image. The controller returns an acknowledgment of
<SOH>1<CR>. This is a positive response. If you receive a negative response
<SOH>0<CR>, you can cancel the calibration by issuing a Reset command and then
start over again.
3. Touch the sensor at an upper right target, which is located 12.5% (1/8) in from the
corner of the video image. The controller returns an acknowledgment of
<SOH>1<CR>. This is a positive response. If you receive a negative response, you
must start over again.
Touching the two valid calibration points results in a successful calibration. If either
calibration point is invalid, the calibration fails. The PX controller restores the previous
calibration values. If Calibrate fails, repeat the CX process.
Guidelines for Calibrate Command
Here are several guidelines for using the Calibrate commands:
?
The controller uses the data immediately before liftoff to register a calibration touch.
Therefore, you can touch the coordinate target, hold for a few seconds, and then lift
off. Instructing users to touch this way results in a more accurate calibration.
?
The controller stores the data in non-volatile memory (NOVRAM). Therefore, you
do not have to calibrate the sensor each time you power on the system. You should,
however, recalibrate the touch sensor any time the video display changes size or
resolution.
?
You can cancel calibration at any time during this sequence by issuing a Reset
command.
Determining Target Areas
The default calibration targets (points) are located 12.5% (1/8) inward from the corners
of the video image. For example, the resolution of your Windows-based display is 1680
x 1050. The Calibrate Extended command calculates the amount to move inward as
follows:
?
Amount to move inward in the X direction: 1680 x 1/8 = 210
?
Amount to move inward in the Y direction: 1050 x 1/8 = 131
The Calibrate Extended command then positions
the first calibration target inward from
the lower left corner (0,1049) and the second calibration target inward from the upper
right corner (1679,0). The following illustration shows how the calibration targets are
calculated for a Windows-based system. Your
operating system may be different.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
M30L40C-E3/4W
DIODE SCHOTTKY 30A 40V TO-220AB
MAN6910
LED 7-SEG DUAL CA RED RHDP .56"
MB203LCD-1
LCD MOD W/CABLE/CONN FOR MB203A
MBD101G
DIODE SCHTTKY 7V LW NOISE TO92-2
MBD110DWT1G
DIODE SCHOTTKY DUAL 7V SOT-363
MBD54DWT1G
DIODE SCHOTTKY DUAL 30V SOT-363
MBR10100CTP
DIODE SCHOTTKY 10A 100V TO220-3
MBR1060CT
DIODE SCHOTTKY 10A 60V TO220-3
相关代理商/技术参数
M225759/34-22-9
制造商:ALCATEL 功能描述:M22759/34-22-9 STR TNC XL-ETFE WHT 150C 600V **QPL/CTR**
M22579/11-22-1
制造商:Carlisle Interconnect Components 功能描述:MIL SPEC HOOK UP WIRE
M22579/11-22-2
制造商:Carlisle Interconnect Components 功能描述:MIL SPEC HOOK UP WIRE
M22579/11-22-5
制造商:Carlisle Interconnect Components 功能描述:PTFE GRN 200C 600V **QPL/CTR** ROHS 制造商:Harbour Industries 功能描述:PTFE YLW 200C 600V
M22579/11-24-5
制造商:JAGUAR INDUSTRIES 功能描述:MIL SPEC HOOK UP WIRE
M22579/16-22-0
制造商:Carlisle Interconnect Components 功能描述:M22759/16-22-0 STR TNC ETFE BLK 150C 600V
M225FAN
制造商:MTRONPTI 制造商全称:MTRONPTI 功能描述:5x7 mm, 3.3 Volt, HCMOS/TTL Compatible Output, Clock Oscillator
M225FCN
制造商:MTRONPTI 制造商全称:MTRONPTI 功能描述:5x7 mm, 3.3 Volt, HCMOS/TTL Compatible Output, Clock Oscillator